Tallahassee Indoor Shooting Range
Likes Likes:  55
Dislikes Dislikes:  0
Page 1 of 4 1234 LastLast
Results 1 to 10 of 37

Thread: 300 blackout ar-15 benefit build for rumbler

  1. #1
    Graduate
    Join Date
    Aug 2012
    Posts
    3,100

    300 blackout ar-15 benefit build for rumbler

    Rumbler needs our help,
    I was looking around and found some new ar 15 parts I had and the best use for them I can come up with for them is a rumbler build..
    If we could get donated items to do a build, it would be added to the auction to benefit rumbler.

    Looks like it will be a nice 300 blackout....
    Complete with reloading components, powder and dies, 7 mags, and a optic, in FDE tan (upper/lower/barrel) the flash hider, stock, handguard and controls in black






    List of donated parts:
    Builder (talon2) a big, big, thanks....

    I'll donate a new stripped upper, a new psa lpk, f/a, and port cover and small parts, and a new anderson stripped lower to the cause.(as well as a pmag) (mapper)

    2 gi mags-(dale gribble)

    4 pmags-(Danman)

    a pound of w296 powder-(jmw4570)

    Set of RCBS AR series small base dies and shellholder in 300 blk (anonymous )


    A keg (4lbs)
    of red dot powder (anonymous)

    gas tube, A2 front sight, front grips, delta ring, buffer tube, buffer, buffer spring, stock and any spring, detent or pin that's needed. -( seadog)

    I'll provide the 16" .300 BLK barrel and cerrakote. (Talon2)

    I will donate 250 pieces of my 300 blackout brass, 250 cci small rifle primers, 250 barrier bullets (one rumblers favorite bullets) 130gr OTM (which makes a great hog killer round). (Marcus6176)

    Bcg and charge handle (harleybrent)

    I have an almost new Primary Arms scope I can donate. It's the zero magnification one that is like an AimPoint. In fact, the rubber AimPoint cover fits it. -(surfer5)




    This will be a nice package...and with the powder, components, and dies make the ammo cost/availibility a non issue, so if anyone was holding off on getting a blackout for those reasons, it is not a concern.. (thanks marcus, jim, and anon donor for that)


    I would like to run this concurrently with the auction.

    http://forum.capitalcitygunforum.com...149#post104149




    This place is great...the community is what sets it apart..

    A big Thanks to everyone who helped make this happen
    Last edited by mapper; October 5th, 2014 at 11:06 AM.

  2. #2
    Graduate
    Join Date
    Aug 2012
    Posts
    3,100
    So this can be a rifle at this point....
    And while the lower is stamped 223/5.56mm, I think it can be other calibers as well...
    Since it was a lower only on the form....and not designated as a pistol or rifle..
    Last edited by mapper; September 19th, 2014 at 05:51 PM.

  3. #3
    CCGF Depository Dale Gribble's Avatar
    Join Date
    May 2012
    Posts
    14,859
    It should be in 300 blackout if we are doing a Rumbler Build.
    When I despair, I remember that all through history the ways of truth and love have always won. There have been tyrants, and murderers, and for a time they can seem invincible, but in the end they always fall. Think of it--always.

  4. #4
    Graduate
    Join Date
    Aug 2012
    Posts
    3,100
    When I said rumbler build, I was not necessarily stating caliber, or configuration. Mainly that it was a build with proceeds to benefit him.

    Whatever parts are donated would dictate what is built...


    But if a blackout barrel gets donated.......
    Last edited by mapper; September 19th, 2014 at 03:01 PM.

  5. #5
    CCGF Depository Dale Gribble's Avatar
    Join Date
    May 2012
    Posts
    14,859
    Oh I know. I wish I had extra parts, but I will put in 2 new steel USGI mags for the effort.
    When I despair, I remember that all through history the ways of truth and love have always won. There have been tyrants, and murderers, and for a time they can seem invincible, but in the end they always fall. Think of it--always.

  6. #6
    Graduate JMW4570's Avatar
    Join Date
    Apr 2012
    Location
    Tally
    Posts
    2,220
    I think it should be dipped in pink camo...
    Weapon of Choice: Illudium Q-36 Explosive Space Modulator bolted to a crappy old T53 stock

  7. #7
    CCGF Waterboy Jmoorewar's Avatar
    Join Date
    Apr 2013
    Location
    My house
    Posts
    3,203
    I have a regular grip if the lpk is missing that. I replaced mine. I don't have the screw to attach it to the lower tho.
    When there is beer involved,we all win.
    Me

    I felt you went over the line a bit,when you theoretically wanted to fornicate with a mythical child.
    Daniel Tosh

  8. #8
    Graduate
    Join Date
    Aug 2012
    Posts
    3,100
    Lpk has grip, it was opened when I got it, and I had someone check it, they said it was all there..
    But posted it like I did incase it was missing any small parts, springs, detents, etc..

  9. #9
    Graduate
    Join Date
    Aug 2012
    Posts
    3,100
    Quote Originally Posted by JMW4570 View Post
    I think it should be dipped in pink camo...
    Wow, thanks!
    I didn't know you did hydrodipping

  10. #10
    Liver Life Giver Highlander's Avatar
    Join Date
    May 2012
    Location
    Tallahassee
    Posts
    894
    Quote Originally Posted by mapper View Post
    Wow, thanks!
    I didn't know you did hydrodipping
    Awesome offer Jim!





    *snicker*

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •