Tallahassee Indoor Shooting Range
Likes Likes:  204
Dislikes Dislikes:  1
Page 1 of 10 12345 ... LastLast
Results 1 to 10 of 95

Thread: Wood Resto and Repair

  1. #1
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720

    Wood Resto and Repair

    Click image for larger version. 

Name:	CoopRest1.jpg 
Views:	170 
Size:	57.7 KB 
ID:	12557 Click image for larger version. 

Name:	CoopRest2.jpg 
Views:	150 
Size:	54.3 KB 
ID:	12558 Click image for larger version. 

Name:	CoopRest3.jpg 
Views:	187 
Size:	61.4 KB 
ID:	12559 Click image for larger version. 

Name:	CoopRest4.jpg 
Views:	191 
Size:	56.6 KB 
ID:	12560 Click image for larger version. 

Name:	CoopRest5.jpg 
Views:	166 
Size:	61.0 KB 
ID:	12561

  2. #2
    Graduate
    Join Date
    May 2012
    Posts
    9,288
    Looks nice, how much does a job like that run?
    Luck is the phenomena created when Preparation meets Opportunity .

  3. #3
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720
    Quote Originally Posted by FLT View Post
    Looks nice, how much does a job like that run?
    Depends on the extent of the damage. Repairing a previously oiled stock is easier. If it's a poly coat with a chip, the entire stock has to be redone. Starts at $80 and goes up from there.

  4. #4
    Graduate polebarn's Avatar
    Join Date
    Apr 2013
    Posts
    12,847
    How much to remove poly from Garand stock AND preserve the dod and p marks?

  5. #5
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720
    Quote Originally Posted by polebarn View Post
    How much to remove poly from Garand stock AND preserve the dod and p marks?
    To remove poly and fix any dings, etc and go back with an oil finish will run about $300. If you'll notice, most war guns have deep and open grains. This allows a lot of moisture to get into the wood and cause potential damage. When we run the finish all the pores get filled, so it looks smooth and uninterrupted across the wood.

  6. #6
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720
    Click image for larger version. 

Name:	Ber6871.jpg 
Views:	141 
Size:	68.4 KB 
ID:	12725 Click image for larger version. 

Name:	Ber6872.jpg 
Views:	140 
Size:	57.0 KB 
ID:	12726 Click image for larger version. 

Name:	Ber6873.jpg 
Views:	143 
Size:	59.7 KB 
ID:	12727 Click image for larger version. 

Name:	Ber6874.jpg 
Views:	131 
Size:	47.8 KB 
ID:	12728 Click image for larger version. 

Name:	Ber6875.jpg 
Views:	131 
Size:	62.8 KB 
ID:	12729 Click image for larger version. 

Name:	Ber6876.jpg 
Views:	153 
Size:	65.6 KB 
ID:	12730

    Fit for spacer and pad for Beretta 687DL

  7. #7
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720
    Click image for larger version. 

Name:	Brassblock1.jpg 
Views:	122 
Size:	45.9 KB 
ID:	12731 Click image for larger version. 

Name:	Brassblock2.jpg 
Views:	135 
Size:	33.5 KB 
ID:	12732 Click image for larger version. 

Name:	Brassblock3.jpg 
Views:	126 
Size:	48.9 KB 
ID:	12733

    Building a jig to bend an engraved brass plate for SxS stock

  8. #8
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720
    Click image for larger version. 

Name:	IthacaPlate.jpg 
Views:	152 
Size:	45.0 KB 
ID:	12738

    Engraved and inlaid brass escutcheon for Ithaca SxS

  9. #9
    Sultan of Tin Foil Jafar's Avatar
    Join Date
    Jul 2013
    Location
    Metcalfe
    Posts
    9,720
    Click image for larger version. 

Name:	Siner1.jpg 
Views:	114 
Size:	62.0 KB 
ID:	12760 Click image for larger version. 

Name:	Siner4.jpg 
Views:	110 
Size:	61.5 KB 
ID:	12761 Click image for larger version. 

Name:	Siner3.jpg 
Views:	140 
Size:	65.4 KB 
ID:	12762

    Began installing a period correct recoil pad on a Burkard and Behr trap shot gun. The German 12 gauge is a break-action design circa early 1900's with a bottom lever that sets the hammer and breaks the barrels. The barrels are marked as Krupp steel and the engraving and final finish were performed by the American company L.C. Siner. An extremely rare piece.

  10. #10
    Dildo Smuggler
    Join Date
    Jan 2017
    Posts
    1,266
    Nice..... are you doing any work with melt in lacquer sticks on wood dings?

    I've seen some years ago that you couldn't tell after they were done.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •