Printable View
Most Russian surplus ammo is going to be berdan primed which is non-reloadable. Prvi makes a brass cased round that you could reuse the brass from. I'm not sure, but you may be able to use standard .308 cal bullets. It would pretty interesting to see what a mosin would do with 175 grain Sierra Match Kings and Varget powder. As far as dumping the powder, you could try using a kinetic bullet puller. You're going to need one anyway if you plan on getting into reloading.
Can you re seat the bullet after you do that or does it need replaced since it has had a case crimped on it? seems like an interesting idea, open it up swap/equalize powder and reseat:rolleyes:
Course I don't know shit about reloading either:D
1. Due to the quality and age of the powder I think you're going to find it a waste of time. Based on YEARS of reloading experience, slight variances in powder charge (.10 to .30 of a grain may not make a measurable difference). The surplus bullets are another lack luster component as well.Quote:
Originally Posted by jlfar0311
2. Tools... you will need a kinetic bullet puller, a press, dies, a scale, a chamfer tool for the case mouths, and a caliper set at minimum.
3. I've had some VERY slight delays in primer ignition with surplus... that's another precision killer... lack of consistency in the powder ignition and burn rate.
4. Forget using .308 bullets.
But hey... it's a project right?
I recommend Lee equipment if you are on a budget and just getting started. For the bullet puller I would suggest the Lyman magnum impact puller for what you are wanting to do. Sierra makes a .311 match king that might work pretty well. It would at least be worth a try.
...or you could scrap the whole plan and just get a 30-06.:D
Yes... while not a well recognized "hang fire"... but a delay discernible enough that lets you know it happened.Quote:
Originally Posted by jlfar0311
As far as brand name for tools... Hornady, Dillon, and RCBS are front runners... 90% of my gear is RCBS. IMO their CS is second to one. You're welcome out ANYTIME I'm up that way... I can talk shop (reloading) for hours...
As far as the bore goes, any good gunsmith should be able to "slug" your barrel to find the tightest overall measurement... you can do it actually by using a wood dowel to drive a lead slug through the bore (chamber to muzzle) and then measure the slug with a caliper. As far as the deviation in bore diameter throughout the entire bore, having it air gauged would tell you but I have no idea who or where you could get it done... or if you could. As you drive a slug down the barrel you might even detect larger areas in the bore just based off resistance.
I fixed it for you... lolQuote:
Originally Posted by silvereagle
. . and lets not forget that mixing powders, even different lots of the "same" powder can have some pretty unpredictable results.
Jlfar, you need to come to the Talon shop. In two hours I can show you far more than you ever wanted to know about the science (and art) of loading ammunition.
DSH offers reloading classes. Purchase supplies through them and you can use their equipment.
Here's some good info and a good site for reference.Quote:
Originally Posted by jlfar0311
http://www.handloadersbench.com/forum5/20203.html
If you want accurate results you need to get every little bit out of the ammo. You won't be able to make a drastic difference by only changing one factor of the ammo.
Jlfar,I have been reloading for 52 yrs,If there is any thing that I can help you with please let me know.If need be you could come to my home an I will sit down an teach you .I have most Rcbs,equip.some different dies,but if you buy the good stuff it will last you forever.Have been using a Rcbs rockchucker press for 40yrs no wear.
You can Pm me or you can call me on my cell 850-210-2377
Jlfar,you can call me most any time.I am retired and just do a lot o piddling around .Always glad to help some one out with the interests I have.
Quote:
Originally Posted by jlfar0311
Slugging the bore is fairly simple but you need the right equipment. Hammering a lead slug the wrong way can damage the bore.
I have been using the slugs from Lead Bullet Technologies. They are specially designed for that purpose. Works easily and can tell you more about bore size and condition. Cost a bit but is worth it.
Proper size bullets are available for the 7.62x54. They are the same as the 303 British, .312. Match bullets are available, too.
I have been loading since 1972 and am always glad to help someone get started. It is easy enough to do but has to be done properly.
Ask here and I will try to answer any questions.