$115.99
Printable View
$115.99
You know, it would probably help if you spelled it correctly.
Steyr.
Na. I think what might be the most help would be mentioning that an abundant source of ammunition exists . . . . if in fact there is one.
I will admit to being intrigued by the rifle. But . . . well . . . you know, a rifle like that without plausible ammunition availability is a . . boat oar. Or a club. or a pole for pole vaulting. Or a . . well you get the idea. :)
LOLQuote:
Originally Posted by Rumbler
Priv makes ammo as does Hornday. Priv also imports bullets and brass. Mine has never shot a round I didn't personally make. Well at least while I've owned it. They are a blast.Quote:
Originally Posted by Rumbler
My guess is these guns will not come with the enbloc clip, which you will need because the extractor does not like being single fed.
Enbloc Clip
http://www.buffaloarms.com/Hungarian...spx?TERM=8x56r
(You can mod the clip to make it stay in the gun, and then feed the clip as a normal fixed magazine as well)
Complete Ammo
http://www.grafs.com/retail/catalog/...ategoryId/257?
Components
http://www.grafs.com/retail/catalog/...roductId/12658
http://www.grafs.com/retail/catalog/...ategoryId/925?
You can also make brass from 7.62x54r brass (or so I've read). Its a few mm shorter but doesn't cause any issues.
Here is mine:
https://lh6.googleusercontent.com/-q...0/DSC_4258.JPG
What about the Swiss K31?
Classic Firearms and Samco Global have some. None of my distributors do at this point.Quote:
Originally Posted by BlueBronco
K31's are great guns, I have one of those also. Straight pull bolt actions are a hoot.
I've seen the .330 bullets, new brass, and dies for the 8x56R on Gunbroker within the last few days.
But has anyone tried paddling with one yet . . . ??
. . seriously though . . . as long as components and load data exists and the enbloc MAGAZINE (see that, Tack?) is available, I'd call that an abundant source. :)
WWWII era 8x56R goes for about a dollar a round now. I have some Hirtenberger made in the late thirties after the Anschluss (when Austria had become a part of Grosse Deutschland) and it is the most ass-kicking ammo I've ever fired in anything short of a .50 BMG. I suspect that Privi probably reduces the charge a bit from that full original military load. The thing about a M-95, though... is that isn't a rifle in the photo. It's either a carbine (small possibility) or a Stutzen (cut down rifle... much more likely). Most of the Gewehrs (long rifles) were cut down to Stutzens in the 1920s and 1930s. I know that perceived recoil is just whatever is perceived... but I swear that the recoil of the full length rifle is even worse than that of the Stutzen. Several Eastern European countries converted long M-95s to what is referred to as M95M configuration to shoot 7.92x57mm (Mauser ammo) after WWII. The recoil on those is more reasonable... but besides the irreplaceable replacement extractor tending to break because the rifle was never intended to handle a rimless round, there is the small matter that although both are called "8mm", Mauser 8mm uses a .321-.323 diameter bullet but "8mm" Mannlicher needs .329 diameter... Mauser bullets tend to sort of bang back and forth side to side as the go down a Mannlicher bore. I haven't checked lately but 8x56R brass has tended over the years to be only episodically available, and .329 isn't a commonly available bullet mold either... but the brass can be made by fireforming 7.62x54 brass... though I can't claim that is always available either. All in all a M-95 of any length is an acquired taste that is hard to feed, but with patience and persistence it can be done. The biggest drawback of all is needing those verdampte enbloc clips. Interestingly, my dad brought one home from WWII. If he ever knew what it was though, I rather suspect that he forgot. When I went through his stuff after he died, he was using it as a giant paper clip.:banana: