Want to Get Into Loading/Reloading

Most Russian surplus ammo is going to be berdan primed which is non-reloadable. Prvi makes a brass cased round that you could reuse the brass from. I'm not sure, but you may be able to use standard .308 cal bullets. It would pretty interesting to see what a mosin would do with 175 grain Sierra Match Kings and Varget powder. As far as dumping the powder, you could try using a kinetic bullet puller. You're going to need one anyway if you plan on getting into reloading.

Can you re seat the bullet after you do that or does it need replaced since it has had a case crimped on it? seems like an interesting idea, open it up swap/equalize powder and reseat:rolleyes:


Course I don't know shit about reloading either:D

Quote:

---

Originally Posted by jlfar0311

Alright, I think I've finally come to the point in my life where I'm no longer satisfied shooting, but want to be the mad scientist and make cool shit to shoot. I know nothing about reloading tools or methods. I recently purchased a book "The ABC's of Reloading." I'm about to read it.

That being said, I think I wanna take Ceddie's advice and dump some of my 7.62x54R rounds and redistribute the powder as exact weights in every round, hoping to increase accuracy. First question, is this a good idea? Second question; what tools and/or equipment would I need to be able to do this. I know everyone's time is valuable and I don't want to seem eager to be spoon fed, so if it's too much to type you can just throw a website or book title at me and I'll go read how to. Thanks for the help.

---

1. Due to the quality and age of the powder I think you're going to find it a waste of time. Based on YEARS of reloading experience, slight variances in powder charge (.10 to .30 of a grain may not make a measurable difference). The surplus bullets are another lack luster component as well.
2. Tools... you will need a kinetic bullet puller, a press, dies, a scale, a chamfer tool for the case mouths, and a caliper set at minimum.
3. I've had some VERY slight delays in primer ignition with surplus... that's another precision killer... lack of consistency in the powder ignition and burn rate.
4. Forget using .308 bullets.

But hey... it's a project right?

I recommend Lee equipment if you are on a budget and just getting started. For the bullet puller I would suggest the Lyman magnum impact puller for what you are wanting to do. Sierra makes a .311 match king that might work pretty well. It would at least be worth a try.

...or you could scrap the whole plan and just get a 30-06.:D

Quote:

---

Originally Posted by jlfar0311

Good thing to know before I tried set up for that.

Any brand you recommend and/or kits that are available with most or all of these tools?

Is this considered a "hang fire" (which I have seen numerous times while running belt-feds) or is this something that is so minute that you can't actually observe? Would it do any good to dump a casing and measure in your own modern powder and make a consistent batch?

Yeah, I did a ton of research on that today. Know of anyway to gauge a bore to see what tolerance it will allow?

And you know I love my projects more than a single black female with 8 illegitimate babies.

---

Yes... while not a well recognized "hang fire"... but a delay discernible enough that lets you know it happened.

As far as brand name for tools... Hornady, Dillon, and RCBS are front runners... 90% of my gear is RCBS. IMO their CS is second to one. You're welcome out ANYTIME I'm up that way... I can talk shop (reloading) for hours...

As far as the bore goes, any good gunsmith should be able to "slug" your barrel to find the tightest overall measurement... you can do it actually by using a wood dowel to drive a lead slug through the bore (chamber to muzzle) and then measure the slug with a caliper. As far as the deviation in bore diameter throughout the entire bore, having it air gauged would tell you but I have no idea who or where you could get it done... or if you could. As you drive a slug down the barrel you might even detect larger areas in the bore just based off resistance.

Quote:

---

Originally Posted by silvereagle

I recommend Lee equipment if you are on a budget and just getting started. For the bullet puller I would suggest the Lyman magnum impact puller for what you are wanting to do. Sierra makes a .311 match king that might work pretty well. It would at least be worth a try.

...or you could scrap the whole plan and just get a .338 Lapua.:D

---

I fixed it for you... lol

. . and lets not forget that mixing powders, even different lots of the "same" powder can have some pretty unpredictable results.

Jlfar, you need to come to the Talon shop. In two hours I can show you far more than you ever wanted to know about the science (and art) of loading ammunition.

DSH offers reloading classes. Purchase supplies through them and you can use their equipment.

Quote:

---

Originally Posted by jlfar0311

Know of anyway to gauge a bore to see what tolerance it will allow?

---

Here's some good info and a good site for reference.
http://www.handloadersbench.com/forum5/20203.html

If you want accurate results you need to get every little bit out of the ammo. You won't be able to make a drastic difference by only changing one factor of the ammo.

Jlfar,I have been reloading for 52 yrs,If there is any thing that I can help you with please let me know.If need be you could come to my home an I will sit down an teach you .I have most Rcbs,equip.some different dies,but if you buy the good stuff it will last you forever.Have been using a Rcbs rockchucker press for 40yrs no wear.
You can Pm me or you can call me on my cell 850-210-2377