Talon Training Group
Likes Likes:  44
Dislikes Dislikes:  0
Page 2 of 5 FirstFirst 12345 LastLast
Results 11 to 20 of 47

Thread: .300 AAC Blackout Load Data

  1. #11
    Junior marcus6176's Avatar
    Join Date
    May 2012
    Location
    Away from the bullshit
    Posts
    397
    Right now I am working on some loads that exceed 3,000 fps with no pressure signs
    Texas Ranger Charlie Miller was minding his own business when a concerned citizen came up to him, noted the hammer back on the big 1911 dangling from the Ranger's belt, and asked, "Isn't that dangerous?" Charlie replied, "I wouldn't carry the son-of-a-bitch if it wasn't dangerous."

  2. #12
    Administrator Rumbler's Avatar
    Join Date
    Apr 2012
    Location
    Right Here
    Posts
    8,178
    I wanna do that. With a 230gr bullet.

    And yes for sure, Marcus's brass is as good or better than any factory brass I have worked with. Because I tend to push the limits little stuff like overall case length is a critical dimension. It is also a good indicator of the quality of work put into the brass because that is a very easy place to get lazy.

    Thus far, and I have loaded hundreds at this point, I have yet to have to reject or rework a single case because of an OCL issue.
    I'd rather be lucky than good, but I'd rather KNOW I'm good than HOPE to get lucky.

  3. #13
    Junior marcus6176's Avatar
    Join Date
    May 2012
    Location
    Away from the bullshit
    Posts
    397
    230 gr bullet for a super? Wow! My only advice for that is to switc to a different powder other than h110. I would try lil gun because it is a little more forgiving when it comes to maxing out a load to try even push that heavy ass bullet for a supersonic
    Texas Ranger Charlie Miller was minding his own business when a concerned citizen came up to him, noted the hammer back on the big 1911 dangling from the Ranger's belt, and asked, "Isn't that dangerous?" Charlie replied, "I wouldn't carry the son-of-a-bitch if it wasn't dangerous."

  4. #14
    Graduate
    Join Date
    May 2012
    Posts
    9,289
    A supersonic load for the Sierra 220 grain MKHP is 15.6 grains of AA1680 with a 7 1/2 Remington primer loaded in A Remington 300BLK case to a over all length of 2.190 . A 16 1/2 inch barrel S&W AR 15 was used to record A average velocity of 1520fps. A Oehler 35P chronograph was used to record these velocities . The the air tempature was 70 degrees at the time they were recorded . This load was safe in the rifle used for these test there were no FTF or FTE the bolt locked open on the last shot. As always use at your own risk . Start at 10% under listed maximum load and work up.
    Luck is the phenomena created when Preparation meets Opportunity .

  5. #15
    Administrator Rumbler's Avatar
    Join Date
    Apr 2012
    Location
    Right Here
    Posts
    8,178
    Got this load proofed just the other day.

    10.9gr of AA1680
    230gr Berger Hybrid bullet
    WSR primer
    2.238 C.O.A.L.

    1055
    1047
    1066
    1049
    1063

    Hits like a sledgehammer at 100 yards.

    Apparently my blackout is breaking in nicely. Carbine gas system on a 16" 1:7 barrel. No suppressor, but this load functions flawlessly. Feeds, extracts, locks the bolt back.
    I'd rather be lucky than good, but I'd rather KNOW I'm good than HOPE to get lucky.

  6. #16
    Administrator Rumbler's Avatar
    Join Date
    Apr 2012
    Location
    Right Here
    Posts
    8,178
    19.1gr Lil Gun
    130gr "barrier" bullet*
    Winchester Small Rifle Primer (WSRP)
    NATO Brass
    Medium crimp (Lee factory crimp die)
    2.038 C.O.A.L.

    ---------------------------------------------------------------------------------

    19.1 Lil Gun
    110gr Nosler Varmageddon bullet
    NATO Brass
    WSRP
    Medium Crimp
    2.025 C.O.A.L.
    -------------------------------------------------------------

    * - Pulled carefully from MK319 Barrier Ammo. The best description of this bullet would be a "two bullets in one projectile" The front is an OTM, jacketed. The back is a solid copper 'slug'.

    A couple of days ago JD (using my blackout) shot a full grown male hog right through it's armor. Entry and exit holes. Pig hit the deck, twitched a little, and expired. This bullet is no joke!
    I'd rather be lucky than good, but I'd rather KNOW I'm good than HOPE to get lucky.

  7. #17
    I just ran across this link that I had saved. I shows the cross sections of a lot of various rifle and pistol ammunition.

    http://www.ar15.com/ammo/project/Amm...m#9x18_Makarov

    Thought some of you would find it useful also.

  8. #18
    Administrator Rumbler's Avatar
    Join Date
    Apr 2012
    Location
    Right Here
    Posts
    8,178
    Latest . . .

    20.2gr of H110
    110gr Barnes TAC-TX
    #400 CCI SRP
    2.240 C.O.A.L.

    The Barns data said this should run 2415FPS out of a 16" barrel. The problem - in my view - is that their recommended C.O.A.L. was 2.250 . . . or just exactly enough to touch front and rear of my USGI magazines. They would fit, but there was absolutely zero "wiggle room". SO . . . . I shortened them .010, dropped off .3 of powder and started working back up from there.

    Where I ended is above. Chronograph said:

    2450
    2442
    2460

    I can live with that. For now . . .
    I'd rather be lucky than good, but I'd rather KNOW I'm good than HOPE to get lucky.

  9. #19
    CCGF Fashionista BR549's Avatar
    Join Date
    Aug 2012
    Posts
    2,008
    Honest no BS question, assuming one had brass, what does it cost to get setup to reload, and then what does it cost per round to reload the 300 BLK?

  10. #20
    CCGF Fashionista BR549's Avatar
    Join Date
    Aug 2012
    Posts
    2,008
    I need a complete idiots guide to reloading setups, tools, extras, etc.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •